TPMS Reset: Mitsubishi Endeavor 2004-2011 Tire Pressure Sensor
Mitsubishi Endeavor 2004-2011 Tire Pressure Monitoring System TPMS Reset
Easy to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Mitsubishi Endeavor for the year 2004, 2005, 2006, 2007, and 2011.
A TPMS Tool and OBDII Module, or another properly formatted TPMS scan tool, is required to perform this procedure.
Procedure using a TPMS Tool and OBDII Module
Relearn Procedure when Replacing a Sensor
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in your TPMS Tool.
3. Select OBDII from your TPMS Tool menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. With the ignition still on, re‐scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.
OBDII Errors
If you see an error on the screen while performing an OBDII Relearn, check to make
sure that the vehicle is in the ON position (not ACC). Also make sure all the connections
are secure.
Errors E1 and E2 ‐ Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Errors E3 and E6 ‐ Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBDII Relearn.
Error E5 ‐ Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.
Procedure using another Properly Formatted Scan Tool
Relearn Procedure when Replacing a Sensor
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the OBDII port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re‐scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.
About Mitsubishi Endeavor
Its design origins can be traced back to the Mitsubishi SSU which debuted at the 1999 North American International Auto Show, although the Endeavor does not share the concept’s mechanical underpinnings. The prototype was powered by a 305 hp (227 kW) version of the 6A13TT 2.5 liter twin-turbo V6, which directed the power to a full-time all wheel drive system through its INVECS-II five-speed automatic transmission and AYC. When the Endeavor debuted, it used the 6G75 3.8 liter V6 offering 215 hp (160 kW) (improved to 225 hp (168 kW) in 2004) and 250 lb⋅ft (339 N⋅m), mated to a four-speed automatic transmission with an optional all-wheel-drive system that splits the torque 50/50 by default. In 2011, the Endeavor again featured a 3.8L V6 but upgraded once more to produce 225 hp (168 kW) and 255 lb⋅ft (346 N⋅m) of torque. It received a mild restyle for the 2006 model year. (Source Wiki)
