TPMS Reset-Lincoln Navigator 2007-2019 Tire Pressure Sensor

Lincoln Navigator 2007-2019 Tire Pressure Monitoring System TPMS Reset

Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Lincoln Navigator 2007, 2010, 2011 and 2019.

A TPMS Tool, or another properly formatted TPMS scan tool, is required to perform this procedure.

 

Relearn Procedure for Models WITH STANDARD IGNITION

1. Inflate all tires to pressure listed on vehicle placard.
2. Leave the driver’s door open during the relearn procedure.
3. Turn ignition to OFF position and press and release brake pedal.
4. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
5. Press and release brake pedal.
6. Turn ignition to OFF position.
7. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
8. Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
9. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
10. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
11. Turn ignition to the OFF position

 

Relearn Procedure for Models WITH PUSH-BUTTON IGNITION

NOTE: some models require the ignition button to be pressed twice, without pressing the brake, to enter the RUN mode (Ignition ON/Engine OFF). If this is the case, then modify steps 4 and 6 as noted.

1. Inflate all tires to pressure listed on vehicle placard.
2. Leave the driver’s door open during the relearn procedure.
3. With the vehicle OFF, press and release the brake pedal.
4. Press the IGNITION BUTTON 5 times (NOTE: 8 times if 2x-to-RUN).
5. Press and release the brake pedal.
6. Press the IGNITION BUTTON 6 times (NOTE: 9 times if 2x-to-RUN).

Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.

7. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once after each sensor has been recognized.
8. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
9. Press the IGNITION BUTTON 1 time to turn the vehicle OFF.

 

About Lincoln Navigator

The fourth-generation Lincoln Navigator uses the Ford T3 platform, developed under the U554 code name. Retaining body-on-frame construction, the Lincoln Navigator (and Ford Expedition) were engineered alongside the 2015 Ford F-150. The four-wheel independent suspension configuration was retained, with a redesigned rear suspension layout.

Shared with the Ford F-150 Raptor, the Lincoln Navigator is equipped with a 450 hp twin-turbocharged 3.5L EcoBoost V6 (although Lincoln has ended its use of the EcoBoost nomenclature). The highest-output engine ever sold by Lincoln, the 3.5L V6 is paired with a 10-speed automatic transmission (replacing the previous 6-speed automatic). (Source Wiki)

Leave a Reply

Your email address will not be published. Required fields are marked *