TPMS Reset: Infiniti G35 2003-2008 Tire Pressure Sensor

TPMS Reset-Infiniti G35 2003-2008 Tire Pressure Sensor

Infiniti G35 2003-2008 Tire Pressure Monitoring System TPMS Reset

Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Infiniti G35 for the year 2003, 2006, 2007 and 2008.

A TPMS Tool and OBDII Module, or another properly formatted TPMS scan tool, is required to perform this procedure.

Procedure using a TPMS Tool and OBDII Module

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in you TPMS Tool .
3. Select OBDII from your TPMS Tool ’s menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool ’s ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool ’s menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. With the ignition still on, re‐scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

OBDII Errors

If you see an error on the screen while performing an OBDII Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.

Errors E1 and E2 ‐ Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Errors E3 and E6 ‐ Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection

Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBDII Relearn.

Error E5 ‐ Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this vehicle requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the OBDII port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re‐scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

 

About Infiniti G35

The G35 sedan underwent a major revision for the 2007 model year. This 2nd generation front-mid (FM) platform underpinning the new G is shared in part with the Infiniti M and has several structural reinforcements around the engine and rear floor area, along with three times more laser welding and 16 percent more spot welds than the old version; overall body stiffness was improved by 40 percent. Single-pivot lower control arms in front replace the 1st gen model’s twin lower links. The G35x sedan uses an ATTESA E-TS all-wheel drive system. (Source Wiki)

Leave a Reply

Your email address will not be published. Required fields are marked *