TPMS Reset: Hyundai Tiburon 2007-2008 Tire Pressure Sensor

TPMS Reset-Hyundai Tiburon 2007-2008 Tire Pressure Sensor

Hyundai Tiburon 2007-2008 Tire Pressure Monitoring System TPMS Reset

Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Hyundai Tiburon for the year 2007 and 2008

Procedure using a TPMS Tool and OBDII Module

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.

2. Select a vehicle make, model and model year, which has OBDII support, in you TPMS Tool .

3. Select OBDII from your TPMS Tool menu.

4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).

5. After all sensor ID’s have been stored, use the TPMS Tool ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.

6. Turn ignition to the ON position with the engine OFF (not the ACC position).

7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.

8. Select Upload Car IDs, from the TPMS Tool menu, and upload the sensor IDs.

9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.

10. Turn the ignition to the OFF position. Re‐scan each sensor.

11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

Note: These vehicles utilize two types of TPMS; lo‐line and hi‐line. Hi‐line systems show the driver individual tire positions and air pressures of all tires. Lo‐line systems do not show individual tire positions and only alter that one of the 4 tires is under inflated. Some models switched systems mid‐year, so be aware of the type of TPMS you are servicing.

OBDII Errors

If you see an error on the screen while performing an OBDII Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.

Errors E1 and E2 ‐ Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Errors E3 and E6 ‐ Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the
vehicles selected set to the MAIN set. Then retry OBDII Relearn.

Error E5 ‐ Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this
vehicle requires a spare. If you did upload a spare, but you received this error,
then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.

2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).

3. Turn ignition to the ON position with the engine OFF (not the ACC position).

4. Connect the scan tool to the OBDII port and upload the sensor IDs.

5. Turn the ignition to the OFF position. Re‐scan each sensor.

6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

 

About Hyundai Tiburon

 

A more comprehensive facelift was launched in November 2006 for the 2007 model year, named the Coupe SIII in markets such as the UK, this time altering the appearance of the car enough to designate it the fourth generation or GK F/L2 reminiscent of the RD1 and RD2 denotations.

The headlights are thinner and angled more aggressively; somewhat similar to the original Tiburon headlights with more straight/sharp lines. The tail lights are similar to the RD2 and GK1 but are somewhat smaller and reflect an aftermarket styling. The fenders lose the “gill fins” and other small changes are seen.

The interior is updated with brushed aluminium accents, new blue backlight scheme for gauges and instrumentation and new seats.

Hyundai later introduced the limited, special edition TSIII (UK). This upgraded, limited edition included quilted leather interior with embroidered logos, stiffer sports suspension, quad exhaust exit pipes, a higher level rear spoiler and an anthracite finish to the alloy wheels. The performance of the TSIII remained the same as the SIII. This is the last model made. (Source Wiki)

Leave a Reply

Your email address will not be published. Required fields are marked *