TPMS Reset: Genesis G80 2017 Tire Pressure Sensor

TPMS Reset-Genesis G80 2017 Tire Pressure Sensor

Genesis G80 2017 Tire Pressure Monitoring System TPMS Reset

Quick to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Genesis G80 for the year 2017.

A TPMS Tool, or another properly formatted TPMS scan tool, is required to perform this procedure.

Procedure using an TPMS Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in you TPMS Tool
3. Select OBDII from your TPMS Tool menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. Turn the ignition to the OFF position. Re‐scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

Note: These vehicles utilize two types of TPMS; lo‐line and hi‐line. Hi‐line systems show the driver individual tire positions and air pressures of all tires. Lo‐line systems do not show individual tire positions and only alter that one of the 4 tires is under inflated. Some models switched systems mid‐year, so be aware of the type of TPMS you are
servicing.

OBDII Errors

If you see an error on the screen while performing an TPMS Tool Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.

Errors E1 and E2 ‐ Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Errors E3 and E6 ‐ Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the
vehicles selected set to the MAIN set. Then retry TPMS Tool Relearn.

Error E5 ‐ Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this
vehicle requires a spare. If you did upload a spare, but you received this error,
then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the TPMS Tool port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re‐scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

 

About Genesis G80

The Genesis G80 Sport is mated with a twin-turbo 3.3-litre V6 engine producing 272 kW (370 PS), features sportier bumpers, quad-exhaust tips, staggered nineteen-inch wheels, and a mesh grille. The vehicle was unveiled at the 2016 Busan Motor Show, followed by the 2016 Los Angeles Auto Show, and the 2017 North American International Auto Show. US models went on sale as 2018 model year vehicles. (Source Wiki)

Leave a Reply

Your email address will not be published. Required fields are marked *