TPMS Reset: Ford Fusion 2010-2019 Tire Pressure Sensor

Ford Fusion 2010-2019 Tire Pressure Monitoring System TPMS Reset
Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Ford Fusion for the year 2010, 2016, 2017, 2018 and 2019.
A TPMS Tool, or another properly formatted TPMS scan tool, is required to perform this procedure.
Relearn Procedure for Models WITH STANDARD IGNITION
1. Inflate all tires to pressure listed on vehicle placard.
2. Leave the driver’s door open during the relearn procedure.
3. Turn ignition to OFF position and press and release brake pedal.
4. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
5. Press and release brake pedal.
6. Turn ignition to OFF position.
7. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
8. Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
9. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
10. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
11. Turn ignition to the OFF position.
Relearn Procedure for Models WITH PUSH-BUTTON IGNITION
NOTE: some models require the ignition button to be pressed twice, without pressing the brake, to enter the RUN mode (Ignition ON/Engine OFF). If this is the case, then modify steps 4 and 6 as noted.
1. Inflate all tires to pressure listed on vehicle placard.
2. Leave the driver’s door open during the relearn procedure.
3. With the vehicle OFF, press and release the brake pedal.
4. Press the IGNITION BUTTON 5 times (NOTE: 8 times if 2x-to-RUN).
5. Press and release the brake pedal.
6. Press the IGNITION BUTTON 6 times (NOTE: 9 times if 2x-to-RUN). Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
7. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once after each sensor has been recognized.
8. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
9. Press the IGNITION BUTTON 1 time to turn the vehicle OFF.
About Ford Fusion
Ford again updated the Fusion for the 2019 model year. This version debuted at the 2018 New York International Auto Show, set to go on sale in late summer 2018.
The 2019 Fusion adds Ford’s “Co-Pilot 360” safety suite as standard on all models. It includes automatic emergency braking, lane-keeping assist, blind-spot and rear-cross-traffic warning systems, automatic highbeams, and automatic wipers.
The new models have updated front and rear styling. The 1.5 L EcoBoost engine is now standard on SE and higher models, except for the V6 Sport, formerly known as Sport. The SEL replaces the SE Luxury Package, and the Platinum is dropped, moving the Titanium up-level. The Hybrid is no longer available in base S trim, and the Energi is available only in Titanium trim. The Energi model’s battery range will increase from 22 miles to 25 miles, and the battery may take less space in the trunk. (Source Wiki)