Key Programming: Toyota Sequoia 1998-2010

Key Programming Toyota Sequoia 1998-2010

Toyota Sequoia 1998-2010 Key Programming Procedure

 

The following are the key programming procedures for the year 2004, 2005, 2006, 2007, 2008, 2009 and 2010 Toyota Sequoia.

 

Toyota Sequoia 1998-2001

TO DELETE ALL BUT ONE KEY FROM THE UNIT:

1. Depress and release brake and accelerator pedals once, doing both at the same time.
2. Put an existing master key into the ignition. Leave the key in the LOCK position; do not turn it.
3. Press and release the accelerator pedal, six times, within 15 seconds of inserting the key.
4. Within 20 seconds of Step 3, press and release the brake pedal seven times.
5. The dashboard security light will flash. This confirms that all keys (except the one currently being used) have been deleted.
6. Within ten seconds, remove the key from the ignition cylinder. This is now the only key still programmed to work.

ADD KEY:

1. Press and release the brake and accelerator pedals once, doing both at the same time.
2. Put the existing master key into the ignition.
3. Press and release the accelerator pedal five times within 15 seconds.
4. Press and release the brake pedal six times within 20 seconds and remove key.
5. Insert new key into ignition within ten seconds.
6. Press and release the accelerator pedal once within ten seconds.
7. The security light will turn off after 80 seconds. This indicates that the new key is now registered.
8. Remove new key. Press and release the brake pedal once.

 

Toyota Sequoia 2002-2010

Keys can be programmed using the Code-Seeker on most 32 bit systems.

TO DELETE ALL BUT ONE KEY FROM THE UNIT:

1. Simultaneously depress and release brake and accelerator pedals 1 time.
2. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF(LOCK) position.
3. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.
4. Within twenty seconds of completing the above step, depress and release the brake seven times.
5. The security light will flash, indicating all keys other than the one being used have been deleted.
6. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

 

ADD DUPLICATE KEY:

Requires one working Toyota/Lexus Master key.

1. Make sure all doors and windows are closed.
2. Insert Master key into the ignition cylinder.
3. Cycle the ignition cylinder from ON to OFF five times.
4. Open and close the driver side door six times.
5. Remove the Master key and insert the new duplicate key.
6. TURN THE IGNITION CYLINDER ON.
7. The new key will be registered after 60 seconds. The THEFT light on the dashboard will go out, indicating that the programming has been completed.

 

 

About Toyota Sequoia

Toyota revealed the 2008 Toyota Sequoia at the Los Angeles Auto Show in November 2007, with sales beginning in December of that year. The new Sequoia, like the original, is based on the new Tundra. The Tundra, on the other hand, has a fully boxed frame, a rear independent suspension with double wishbones and coil springs for increased ride comfort and room, and a locking center differential on 4-wheel drive variants. The revised suspension gives the Sequoia a 19-foot (5.8-meter) turning radius and enables for a fold-flat rear seat. Toyota claims that the redesigned frame is 70% more resistant to bending flex and has a 30% increase in torsional rigidity[5]. The new Sequoia, on the other hand, weights 500 lb (227 kg) more than the previous model. The coefficient of drag has been lowered to 0.35.

A ULEV-II compliant 381 horsepower 5.7 L 3UR-FE V8 paired to a 6-speed automatic is available as an option.

Leave a Reply

Your email address will not be published. Required fields are marked *