Key Programming: GMC Envoy 2006-2010
GMC Envoy 2006-2010 Key Programming Procedure
The following are the key programming procedures for GMC Envoy for the year 2006, 2007, 2008, 2009 and 2010.
NOTE:
On-Board Programming for use in most GM vehicles for model years 2006-2010. Some vehicles may require a dealer or aftermarket programming tool. Most GM vehicles for model years 2011- 2012 require a dealer or aftermarket programming tool.
USE THIS PROCEDURE FOR VEHICLES WITH DRIVER INFORMATION CENTER BUTTONS:
RELEARN REMOTE:
This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters.
1. Press the vehicle information button until PRESS V TO RELEARN REMOTE displays.
2. Press the set/reset button until REMOTE LEARNING ACTIVE is displayed.
3. Press and hold the lock and unlock buttons on the first transmitter at the same time for about 15 seconds. On vehicles with memory recall seats, the first transmitter learned will match driver 1 and the second will match driver 2. A chime will sound indicating that the transmitter is matched.
4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it.
5. To exit the programming mode, you must cycle the key to LOCK/OFF.
USE THIS PROCEDURE FOR VEHICLES WITHOUT DRIVER INFORMATION CENTER BUTTONS:
REMOTE:
To access this display, the vehicle must be in P (Park). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine)
1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display.
3. Press and hold the lock and unlock buttons on the keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key. Test remote(s).
About GM Envoy
The GMT360 chassis architecture is used in the second generation GMC Envoy. The GMT360 chassis was created from the ground up for SUV use, putting an end to its resemblance to GM compact pickup trucks. The frame rails are hydroformed and entirely boxed the entire length of their length. The wheelbase lengthened to 113 inches (six inches longer than the first generation); for the first time, an extended-wheelbase version with a 129-inch wheelbase length was produced (1 inch shorter than the GMC Yukon XL).
The independent double-wishbone front suspension was equipped with Bilstein shock absorbers. The rear suspension had a 5-link solid rear axle with load-leveling air suspension as an option.
The second-generation Envoy came standard with four-wheel disc brakes.
The second generation GMC Envoy was debuted as a 2002 model in early 2001. (skipping the 2001 model year). The 2002 Envoy replaced the GMC Jimmy five-door in the same way that the Chevrolet Trailblazer replaced the Chevrolet (S-10) Blazer.
The Envoy was named Sport/Utility Car of the Year by Motor Trend magazine in 2002. From 2002 through 2005, the 4200 Vortec 4200 engine I6 engine was awarded one of Ward’s 10 Best Engines.
For the 1998 model year, GMC debuted the first generation Envoy. The Envoy, which debuted a year before the Chevrolet TrailBlazer, was the highest-trim version of the GMC Jimmy SUV. The Envoy, like the Oldsmobile Bravada, had a leather-trimmed interior, a floor-mounted shifter, and a mainly monochrome exterior with aluminum-alloy wheels. The Envoy trim, like the TrailBlazer and Bravada, was only available in five-door form.
