TPMS Reset: Lexus IS F 2008-2015 Tire Pressure Sensor

Lexus IS F 2008-2015 Tire Pressure Monitoring System TPMS Reset
Quick to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Lexus IS F 2008, 2013, 2014 and 2015.
A TPMS Tool and OBD II Module, or another properly formatted TPMS scan tool, are required to perform this procedure.
Relearn Procedure when Replacing a Sensor
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select OBD II from your Tool’s menu.
3. Starting with the LF tire, use your Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
4. After all sensor IDs have been read, turn ignition to the ON position with the engine OFF (not the ACC position).
5. Connect the OBD II Connector to the Tool then to the vehicle’s OBD II port. Make sure your connection is secure and the green light is on.
6. Select UPLOAD CAR IDS, from the Tool’s menu, and upload the sensor IDs.
7. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
8. To verify the baseline tire pressures are correct, set the parking brake, then hold down the PRESSURE WARNING RESET SWITCH (located near the driver’s side knee bolster or in the glove box) until the TPMS telltale blinks 3 times. If the vehicle is not equipped with this RESET SWITCH, proceed to step 9.
9. With the ignition still in the ON position, re-scan each sensor.
10. Drive the vehicle above 25 MPH, for at least 10 minutes, and monitor the low tire pressure monitor to ensure it does not blink.
Relearn Procedure when Resetting the Tire Pressure or after Rotating the Tires
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Apply parking brake and turn ignition to ON position with the engine OFF (not the ACC position).
3. Hold down pressure warning reset switch (located under the steering wheel or in glove box) until the TPMS telltale light blinks three (3) times.
4. It will take several minutes for the ECU to receive the signals from the sensors and complete initialization.
Note: Many Toyota/Lexus SUV’s and Minivans have a Main/2nd Button to store two sets of sensor IDs. (when using summer and winter tires/wheels). When the Button is not pressed, the vehicle monitors the Main ID’s on the vehicle. When the Button is pressed, the vehicle can monitor a 2nd (set of) ID’s. If Button is pressed, and no ID’s are stored under the 2nd position, the TPMS MIL will illuminate, so ensure you are writing the sensor IDs to the correct position.
OBD II Errors
If you see an error on the screen while performing an OBD II Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.
Errors E1 and E2 – Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Errors E3 and E6 – Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBD II Relearn.
Error E5 – Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this vehicle requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.
Toyota Loop
If you receive E1, E2, E3, or E4 on a Toyota/Lexus vehicle, after verifying a good connection, the vehicle may be stuck in a loop. This happens when the “SET” button is pressed after introducing new sensors to the vehicle. After step 5. (above), select UNLOCK ECU from you Tool’s menu. After successfully unlocking the ECU, perform the OBD II relearn starting with step 2. (above).
About Lexus IS F
The Lexus IS F debuted at the North American International Auto Show on 8 January 2007. The vehicle features a 5.0 L direct-injected V8 producing 416 SAE hp (423 PS, 311 kW) at 6,600 rpm, while peak torque is 371 ft⋅lbf (503 N⋅m) at 5,200 rpm. The engine also features a two-stage intake system, engine oil and automatic transmission fluid coolers and an oil pump designed for high-speed cornering. Compared to the 2GR-FSE V6, 306 hp (228 kW) IS 350, the IS F features a 2UR-GSE V8 engine and over 400 hp (300 kW). The IS F was scheduled to be in dealerships by early 2008.
The IS F made its European premiere at the Frankfurt Motor Show in September 2007, and premiered in Japan at the Fuji Speedway in October 2007. The vehicle went on sale in late 2007 in Japan, in early 2008 in the United States, and in Europe in 2008. (Source WIki)