TPMS Reset: Lexus GS300 2005-2006 Tire Pressure Sensor
Lexus GS300 2005-2006 Tire Pressure Monitoring System TPMS Reset
Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Lexus GS300 2005 and 2006.
A TPMS Tool and OBD II Module, or another properly formatted TPMS scan tool, are required to perform this procedure.
Relearn Procedure when Replacing a Sensor
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select OBD II from your Tool’s menu.
3. Starting with the LF tire, use your Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
4. After all sensor IDs have been read, turn ignition to the ON position with the engine OFF (not the ACC position).
5. Connect the OBD II Connector to the Tool then to the vehicle’s OBD II port. Make sure your connection is secure and the green light is on.
6. Select UPLOAD CAR IDS, from the Tool’s menu, and upload the sensor IDs.
7. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
8. To verify the baseline tire pressures are correct, set the parking brake, then hold down the PRESSURE WARNING RESET SWITCH (located near the driver’s side knee bolster or in the glove box) until the TPMS telltale blinks 3 times. If the vehicle is not equipped with this RESET SWITCH, proceed to step 9.
9. With the ignition still in the ON position, re-scan each sensor.
10. Drive the vehicle above 25 MPH, for at least 10 minutes, and monitor the low tire pressure monitor to ensure it does not blink.
Relearn Procedure when Resetting the Tire Pressure or after Rotating the Tires
1. Inflate all tires to the pressure listed on the vehicle placard.
2. Apply parking brake and turn ignition to ON position with the engine OFF (not the ACC position).
3. Hold down pressure warning reset switch (located under the steering wheel or in glove box) until the TPMS telltale light blinks three (3) times.
4. It will take several minutes for the ECU to receive the signals from the sensors and complete initialization.
Note: Many Toyota/Lexus SUV’s and Minivans have a Main/2nd Button to store two sets of sensor IDs. (when using summer and winter tires/wheels). When the Button is not pressed, the vehicle monitors the Main ID’s on the vehicle. When the Button is pressed, the vehicle can monitor a 2nd (set of) ID’s. If Button is pressed, and no ID’s are stored under the 2nd position, the TPMS MIL will illuminate, so ensure you are writing the sensor IDs to the correct position.
OBD II Errors
If you see an error on the screen while performing an OBD II Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.
Errors E1 and E2 – Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Errors E3 and E6 – Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBD II Relearn.
Error E5 – Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this vehicle requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.
Toyota Loop
If you receive E1, E2, E3, or E4 on a Toyota/Lexus vehicle, after verifying a good connection, the vehicle may be stuck in a loop. This happens when the “SET” button is pressed after introducing new sensors to the vehicle. After step 5. (above), select UNLOCK ECU from you Tool’s menu. After successfully unlocking the ECU, perform the OBD II relearn starting with step 2. (above).
About Lexus GS300
Italdesign Giugiaro began the first design drawings of the GS 300 in 1988. The design firm aimed to produce a deluxe saloon which did without the numerous exterior features and detailing found on existing Japanese premium sedans, in favor of a more simplified, European-style appearance. The vehicle’s exterior styling blended elements of the then-current Lexus LS flagship and SC performance coupe in a rounded, aerodynamic wedge-like shape which featured a high rear decklid and longer and wider proportions than rival vehicles.
The exterior produced a drag coefficient of Cd=0.31. The offered color schemes included single-tone bumper and body finishes, along with dual-tone schemes. Similarities with an Italdesign concept car which debuted in 1990, the Jaguar Kensington, led some observers to suggest that the GS 300 was derived from its design, but the firm has stated that the GS 300 was developed earlier. Equipped with an independent, double-wishbone suspension setup at both front and rear ends, Italdesign’s saloon design first appeared in Toyota Aristo form in Japan in October 1991. (Source Wiki)
