TPMS Reset-Nissan NV2500 2012-2019 Tire Pressure Sensor

TPMS Reset: Nissan NV2500 2012-2019 Tire Pressure Sensor

Nissan NV2500 2012-2019 Tire Pressure Monitoring System TPMS Reset

Easy to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Nissan NV2500 for the year 2012 and 2019.

A TPMS Tool and OBDII Module, or another properly formatted TPMS scan tool, is required to perform this procedure.

 

Procedure using a TPMS Tool and OBDII Module

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in your TPMS Tool.
3. Select OBDII from your TPMS Tool’s menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool’s ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool’s menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. With the ignition still on, re-scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire 
pressure monitor to ensure it does not blink.

 

OBDII Errors

If you see an error on the screen while performing an OBDII Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.

Errors E1 and E2 – Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Errors E3 and E6 – Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBDII Relearn.

Error E5 – Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this vehicle requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the OBDII port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re-scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire 
pressure monitor to ensure it does not blink.

About Nissan NV2500

The NV2500 HD (HD for “heavy duty”) is equipped with the 4-litre V6 engine, with the bigger V8 available as an option. The payload is 3,142 lb (1,425 kg), similar to the GMC/Chevrolet cargo van using the same “2500” designation, and informally known as a “three-quarter-ton”. It comes in S, SV, or SL trim levels and is available in low or high roof; the SL is only available with the V8. The SV trim features a lockable center console with power outlets as well as an additional 120 V outlet in the cargo compartment along with features from the 1500 SV while the SL trim adds chrome bumpers, grille, and door handles and 17″ chrome wheels. (Source Wiki)

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *