TPMS Reset-Nissan Altima 2006-2019 Tire Pressure Sensor

TPMS Reset: Nissan Altima 2006-2019 Tire Pressure Sensor

Nissan Altima 2006-2019 Tire Pressure Monitoring System TPMS Reset

Easy to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Nissan Altima for the year 2006, 2012, 2015, 2018 and 2019.

 

A TPMS Tool and OBDII Module, or another properly formatted TPMS scan tool, is required to perform this procedure.

Procedure using a TPMS Tool and OBDII Module

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in your TPMS Tool.
3. Select OBDII from your TPMS Tool’s menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool’s ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool’s menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. With the ignition still on, re-scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire 
pressure monitor to ensure it does not blink.

OBDII Errors

If you see an error on the screen while performing an OBDII Relearn, check to make sure that the vehicle is in the ON position (not ACC). Also make sure all the connections are secure.

Errors E1 and E2 – Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Errors E3 and E6 – Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.

Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the vehicles selected set to the MAIN set. Then retry OBDII Relearn.

Error E5 – Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this vehicle requires a spare. If you did upload a spare, but you received this error, then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the OBDII port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re-scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire 
pressure monitor to ensure it does not blink.

 

About Nissan Altima

The sixth-generation Altima debuted at the 2018 New York International Auto Show. The design was previewed by the Nissan Vmotion 2.0 Concept.

The car can be either be powered by a 188 hp (140 kW) 2.5-liter naturally aspirated direct injected four-cylinder engine or a 248 hp (185 kW) 2.0-liter variable compression turbocharged four-cylinder engine that replaces the V6 powertrain in the previous generation. It is the world’s first production ready variable compression turbo engine. All engines are mated to a continuous variable transmission. All Wheel Drive is only available on the 2.5-liter engine models. (Source Wiki)

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *