TPMS Reset-Mitsubishi Eclipse 2006-2007 Tire Pressure Sensor

TPMS Reset: Mitsubishi Eclipse 2006-2007 Tire Pressure Sensor

Mitsubishi Eclipse w/ Steel Wheels 2006-2007 Tire Pressure Monitoring System TPMS Reset

Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Mitsubishi Eclipse for the year 2006 and 2007.

A TPMS Tool and OBDII Module, or another properly formatted TPMS scan tool, is required to perform this procedure.

 

Procedure using a TPMS Tool and OBDII Module

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Select a vehicle make, model and model year, which has OBDII support, in your TPMS Tool.
3. Select OBDII from your TPMS Tool’s menu.
4. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
5. After all sensor ID’s have been stored, use the TPMS Tool’s ▲ or ▼ button to move the cursor under the letters OBD. Then press the enter button.
6. Turn ignition to the ON position with the engine OFF (not the ACC position).
7. Connect the OBDII Connector to the TPMS Tool then to the vehicle’s OBDII port. Make sure your connection is secure and the green light, on the OBII Module, is on.
8. Select Upload Car IDs, from the TPMS Tool’s menu, and upload the sensor IDs.
9. When RELEARN COMPLETE / IDs UPLOADED TO CAR is displayed, the ID’s have been successfully uploaded.
10. With the ignition still on, re‐scan each sensor.
11. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

OBDII Errors

If you see an error on the screen while performing an OBDII Relearn, check to make
sure that the vehicle is in the ON position (not ACC). Also make sure all the connections
are secure.
Errors E1 and E2 ‐ Reading Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection.
Errors E3 and E6 ‐ Writing Communication Errors
Make sure vehicle is ON and not ACC Check for secure connection
Error E4 – Wrong Set Error
Many Lexus vehicles can store more than one set of TPMS ID’s in ECU. Toggle the
vehicles selected set to the MAIN set. Then retry OBDII Relearn.
Error E5 ‐ Spare Tire Error
If you receive this error, and you did not upload a sensor ID for the spare, then this
vehicle requires a spare. If you did upload a spare, but you received this error,
then the vehicle does not store the ID in the ECU for the spare tire.

Procedure using another Properly Formatted Scan Tool

Relearn Procedure when Replacing a Sensor

1. Inflate all tires to the pressure listed on the vehicle placard.
2. Starting with the LF tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped).
3. Turn ignition to the ON position with the engine OFF (not the ACC position).
4. Connect the scan tool to the OBDII port and upload the sensor IDs.
5. Turn the ignition to the OFF position. Re‐scan each sensor.
6. Drive the vehicle above 30mph for at least 10 minutes and monitor the low tire pressure monitor to ensure it does not blink.

 

About Mitsubishi Eclipse

The first two generations (1G and 2G) share the automobile platform and parts with the rebadged Eagle Talon and Plymouth Laser captive imports. They were built during Mitsubishi Motors’ close relationship with Chrysler Corporation. Their partnership was known as Diamond-Star Motors (DSM). In Japan, the first two generations were sold at a specific Japanese retail chain called Mitsubishi Car Plaza. (2000/2005) The third-generation (3G) shared a redesigned platform with the Chrysler Sebring and Dodge Stratus. During May 2005, the fourth, and final,(2006/2012) generation (4G) Eclipse was introduced, replacing the Chrysler platform used in the first three generations with the PS platform. (Source Wiki)

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *