TPMS Reset-Ford Flex 2009-2019 Tire Pressure Sensor

TPMS Reset: Ford Flex 2009-2019 Tire Pressure Sensor

Ford Five Flex 2009-2019 Tire Pressure Monitoring System TPMS Reset

Simple to follow procedure on how to reset/relearn the TPMS service maintenance indicator warning light on Ford Flex for the year 2009, 2010, 2011 and 2019.

A TPMS Tool, or another properly formatted TPMS scan tool, is required to perform this procedure.

Relearn Procedure for Models WITH STANDARD IGNITION

1. Inflate all tires to pressure listed on vehicle placard.

2. Leave the driver’s door open during the relearn procedure.

3. Turn ignition to OFF position and press and release brake pedal.

4. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.

5. Press and release brake pedal.

6. Turn ignition to OFF position.

7. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.

8. Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.

9. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.

10. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.

11. Turn ignition to the OFF position.

Relearn Procedure for Models WITH PUSH-BUTTON IGNITION

NOTE: some models require the ignition button to be pressed twice, without pressing the brake, to enter the RUN mode (Ignition ON/Engine OFF). If this is the case, then modify steps 4 and 6 as noted.

1. Inflate all tires to pressure listed on vehicle placard.

2. Leave the driver’s door open during the relearn procedure.

3. With the vehicle OFF, press and release the brake pedal.

4. Press the IGNITION BUTTON 5 times (NOTE: 8 times if 2x-to-RUN).

5. Press and release the brake pedal.

6. Press the IGNITION BUTTON 6 times (NOTE: 9 times if 2x-to-RUN). Horn will sound once, and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.

7. Starting with the LF tire, use your TPMS Tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once after each sensor has been recognized.

8. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.

9. Press the IGNITION BUTTON 1 time to turn the vehicle OFF.

About Ford Flex

The Ford Flex is a full-size crossover SUV or wagon that was manufactured by the Ford Motor Company; a single generation was produced from the 2009 to 2019 model years. Introduced as the successor to the Ford Taurus X, the model line also functionally replaced the Ford Freestar minivan. Slightly larger than its predecessor, the Flex was sized between the Explorer and standard-wheelbase Expedition in the Ford model line.

Introduced in 2005 as a concept vehicle, the Flex shifted body configurations from an MPV to a 5-door wagon for production to better meet consumer demand. The model line is based on the Ford D4 chassis architecture, a flexible-wheelbase variant of the Ford D3 platform. The D4 chassis was also shared by the 2011-2019 Explorer and the Lincoln MKT; while sharing no body panels, the MKT served as a direct counterpart of the Flex. (Source Wiki)

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *