KeyFob RKE Programming Procedure-Ford Puma 1997-2002

KeyFob RKE Programming Procedure: Ford Puma 1997-2002

Ford Puma 1997-2002 KeyFob Remote Keyless Entry Programming Procedure

 

 

Programming Procedure – Infrared key fobs

Note. If the central locking / alarm system is malfunctioning, key fob batteries have been replaced or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly.

 

  • Obtain all keys fitted with remote key fob for vehicle
  • Using any key, switch the ignition to position “I”
  • Wait approximately 10 seconds
  • System Alarm LED should illuminate

Note. System Alarm LED illuminates for approximately 5 seconds

  • Whilst system Alarm LED is illuminated:
    o Switch the ignition “OFF” and remove the key
  • Programming mode activated for approximately 20 seconds (System alarm LED remains illuminated):
  • Point the key fob at the infrared receiver
    • Fiesta and Puma: located near interior lamp
  • Mondeo: located in front door handles
    • Press and hold the “Unlock” button on the key fob

 

KeyFob RKE Programming Procedure: Ford Puma 1997-2002

 

    • After approximately 1 second, the LED on the key fob will flash once
    • Press and release the “Lock” button on the key fob between 3 to 5 times, whilst still holding in the “Lock” button on the key fob
    • Release the “Unlock” button on the key fob
    • Continue to point the key fob at the infrared receiver until both the system
    • Alarm LED and key fob LED have flashed 5 times
  • Repeat above procedure to re-program any remaining key fobs.
  • To exit programming mode: Switch ignition “ON” and “OFF” and wait approximately 20 seconds
  • Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons

 

Note. A maximum of 4 key fobs can be programmed to the vehicle.

 

Programming Procedure – Radio frequency key fobs

Fiesta and Puma vehicles only

 

Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly.

 

  • Obtain all keys fitted with remote key fobs
  • Switch the ignition “ON” 4 times within 3 seconds
  • Switch the ignition “OFF” and remove key from ignition switch
  • Programming mode activated for approximately 20 seconds (System alarm LED remains illuminated):
    • Type 1 key fob: Press and release either the “Lock” or “Unlock” button on the key fob

KeyFob RKE Programming Procedure: Ford Puma 1997-2002

    • Type 2 Key fob: Press and release any button on the key fob

KeyFob RKE Programming Procedure: Ford Puma 1997-2002

  • According to model: Wait for either the System Alarm LED or Fog lamps “ON” warning lamp to illuminate and / or the vehicle to emits an audible warning sound to indicate correct programming
  • Within 20 seconds: Repeat above procedure to re-program any remaining key fobs.
  • To exit programming mode: Switch ignition “ON” and wait 20 seconds
  • Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons.

 

Note. A maximum of 4 key fobs can be programmed to the vehicle.

 

 

About Ford Puma

The Puma was only sold in Europe. Production ended in 2001, although sale of stock vehicles continued into 2002. Ford did not replace it with another small coupé, and instead introduced the Ford StreetKa, a two-seater convertible based on the Fiesta like the Puma was. The StreetKa also borrowed the Puma’s transmission and suspension. About 9,191 Ford Pumas (including cars declared as SORN) remain registered with the DVLA in the UK as of Q3 2020. (Source Wiki)

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *